Ensurepass.com : Ensure you pass the IT Exams
2018 Aug Cisco Official New Released 642-035
100% Free Download! 100% Pass Guaranteed!
Troubleshooting Cisco Unified Computing
Question No: 21
You use dynamic vNICs. You create a new service profile. You receive an error message that indicates that you exceeded the number of dynamic vNICs. Which two components can affect the maximum number of dynamic vNICs in the Cisco UCS environment? (Choose two.)
-
the model of the fabric interconnects
-
the number of chassis uplinks
-
the model of the FEX
-
VMDirectPath sizing
Answer: A,B
Question No: 22
Which two statements about configuring a traffic monitoring session are true? (Choose two.)
-
You can set a local VM as a traffic destination.
-
You can have up to two active monitoring sessions simultaneously.
-
An unlimited number of monitoring session can be stored.
-
A newly created monitoring session is enabled by default.
-
A destination port can also be a source port within the same session.
-
A vHBA can be a source for either an Ethernet or Fibre Channel monitoring session, but not both.
Answer: B,F
Question No: 23
Refer to the exhibit. Which command was executed on a Cisco UCS Fabric Interconnect in NX-OS mode to produce this output?
-
show flogi database
-
show npv flogi-table
-
show flogi
-
show npv flogi-database
-
show fcns database
Answer: B
Question No: 24
Which three Cisco UCS server components can be upgraded via a host firmware package? (Choose three.)
-
BIOS
-
Cisco UCS Manager
-
I/O module
-
Cisco IMC
-
fabric interconnect
-
adapter
-
board controller
Answer: A,F,G
Question No: 25
When configuring a traffic-monitoring session, which two guidelines are required to complete the task? (Choose two.)
-
For Ethernet traffic, the destination must be an unconfigured physical port.
-
For Fibre Channel, the destination must be a Fibre Channel uplink port.
-
For Ethernet traffic, the destination must be an active port that is assigned to an existing VLAN.
-
For Fibre Channel, the destination must be an inactive port on a VSAN.
Answer: A,B
Question No: 26
You have remote CLI access using SSH to the Cisco UCS equipement of a customer. Which command must you use to check for system errors in the UCS domain?
-
show fault
-
show cluster
-
show chassis
-
show failover
Answer: A
Question No: 27
Which protocols can be used to send to Cisco TAC (Technical Assistance Center) the show tech-support command output information about the Cisco UCS domain? (Choose two.)
-
TFTP
-
FTP
-
SCP
-
Telnet
-
SecureTelnet
Answer: B,C
Question No: 28
What is the maximum number of boot targets for an FCoE vHBA on a Cisco UCS C-Series server?
-
1
-
2
-
3
-
4
Answer: D
Question No: 29
On a Cisco UCS C-Series Rack-Mount Server, which state of the DIMM fault LED indicates a faulty DIMM module?
-
OFF
-
flashing red
-
solid amber
-
flashing amber
-
flashing blue
Answer: C
Question No: 30
Which CLI command should you use to promote the local fabric interconnect to primary?
-
cluster primary force
-
cluster failover primary
-
cluster force primary
-
cluster failover
-
failover
Answer: C
100% Ensurepass Free Download!
–642-035 PDF
100% Ensurepass Free Guaranteed!
–642-035 Dumps
EnsurePass | ExamCollection | Testking | |
---|---|---|---|
Lowest Price Guarantee | Yes | No | No |
Up-to-Dated | Yes | No | No |
Real Questions | Yes | No | No |
Explanation | Yes | No | No |
PDF VCE | Yes | No | No |
Free VCE Simulator | Yes | No | No |
Instant Download | Yes | No | No |